.25 Case Spinner third from left for cases from 1.456 to 2.500 long

$19.95

Super convenient to spin clean entire exterior of your .25 cal. cases including the base. Works with cases from 1.456″ to 2.500″ long.  Most use 0000 steel wool (not included).  While a case is spinning its easy to clean the primer pocket with an appropriate tool made for this purpose.  Chucked the spinner in an electric hand drill, or drill press, turn at 400 to 500 rpm. DO NOT WRAP POLISHING MEDIA AROUND YOUR HAND, DO NOT USE GLOVES, GRIP CASES WITH THE POLISHING MEDIA NOT THE BARE HAND. POSTPAID!

 

SKU: 520 Category:

Description

Super convenient to spin clean entire exterior of your .25 cal. cases including the base. Works with cases from 1.456″ to 2.500″ long.  Most use 0000 steel wool (not included).  While a case is spinning its easy to clean the primer pocket with an appropriate tool made for this purpose.  Chucked the spinner in an electric hand drill, or drill press, turn at 400 to 500 rpm. DO NOT WRAP POLISHING MEDIA AROUND YOUR HAND, DO NOT USE GLOVES, GRIP CASES WITH THE POLISHING MEDIA NOT THE BARE HAND. POSTPAID!

 

Reviews

There are no reviews yet.

Be the first to review “.25 Case Spinner third from left for cases from 1.456 to 2.500 long”

Your email address will not be published. Required fields are marked *

Related products

  • .45-110 Cartridge Case Headspace gage

    Rated 0 out of 5
    $19.95     Add to cart

    .45-110 Cartridge Case Headspace gage

    .45-110 stainless steel headspace gage.  Precision shooters benefit by sorting cases into batches according to case headspace variations.  This gage can be used with a caliper, however for the most precise measurements use our Ultimate Cartridge Check System, it eliminates pressure variations when using a caliper, POSTPAID!

    SKU: 850 Category:
    $19.95

  • .45 Cal. spinner on far right for cases from 2.300″ to 2.714″ long

    Rated 0 out of 5
    $19.95     Add to cart

    .45 Cal. spinner on far right for cases from 2.300″ to 2.714″ long

    Super convenient to spin clean entire exterior of your .45 cases including the base.  Works with cases from 2.300″ to 2.714″ long. Most use 0000 steel wool (not included).  While a case is spinning its easy to clean the primer pocket with an appropriate tool made for this purpose.  Chucked the spinner in an electric hand drill, or drill press, turn at 400 to 500 rpm. DO NOT WRAP POLISHING MEDIA AROUND YOUR HAND, DO NOT USE GLOVES, GRIP CASES WITH THE POLISHING MEDIA NOT THE BARE HAND. POSTPAID!

    SKU: 570 Category:
    $19.95

  • Sinclair # 749-009-211 .338 bullet comparator

    Rated 0 out of 5
    $19.95     Add to cart

    Sinclair # 749-009-211 .338 bullet comparator

    .338 Sinclair 749-009-211 bullet comparator.  This precision fixture has a large stable base affording precision measurement.  Use with bullets only or loaded ammunition.   Precision bored with a throat reamer to accurately duplicate a rifle throat.  Carefully drop a bullet or loaded round into the comparator then place on the granite surface of our Ultimate Cartridge Check System. By using this method accurate bullet ogive comparisons are made avoiding pressure variations using a caliper. Bullets shown not included, POSTPAID!

    SKU: 720 Category:
    $19.95

  • Sinclair 749-011-472WB .22-250, .223 & .243 WSSMl Bump Gage Insert 28 Deg.

    Rated 0 out of 5
    $13.99     Add to cart

    Sinclair 749-011-472WB .22-250, .223 & .243 WSSMl Bump Gage Insert 28 Deg.

    SINCLAIR  749-011-472 SHOULDER  BUMP GAGE INSERT. For cartridge cases; 22-250 Remington, 223  & .243 WSSM (Winchester Super Short Mag), & other cases up to 6.5mm with 28° shoulder.    Used to measure the amount of shoulder bump when setting up sizing die. Bump gage is the most accurate when used on the granite surface plate of our Ultimate Cartridge Check System. Recommended bump of .001 to .002 shoulder setback for bolt actin guns and .005 for Semi-Auto and other repeating actions. POSTPAID!

    SKU: 710 Category:
    $13.99